Elite Garage Door are professional garage door service specialists, we have virtually handled every issue you can imagine with regards to garage door repairs. While there are instances you might be able to fix the problem yourself, there are lots of times when it might be best to entrust the garage door repair to the professionals. However, figuring out what’s wrong with your garage door will help you evaluate if it is a problem you can handle or you need to call a professional to help you troubleshoot your garage door issues, below are the top reasons your garage door won’t work.

The Transmitter Batteries Are Dead

If your garage door is not opening with the remote, your garage door transmitters require electrical power to function. If the batteries in your transmitter are old, the transmitter won’t send out a signal to your door to open. First, find out if the transmitter on the wall inside your garage still opens your door when pressed. If it opens, then the transmitter in your car possibly needs battery replacement.

Your Photo Eye Is Out Of Alignment

In the event you notice that the garage door is not opening fully, there may be a problem with the photo eyes, otherwise known as safety sensors. the first thing you’ll need to do is check out the photo eyes. In the long run, these eyes can get dirty, making the light from the beam to be blocked. Also they can gradually become misaligned, making the eyes to not match on each side.

The Track Is Not Aligned Properly

If your garage door is not opening all the way the track may no longer be in alignment, this is usually a serious problem. The metal track your door runs on must be aligned correctly to ensure that your door moves. If you happen to see gaps between the rollers and rail, or bends in the rails, you have an issue. The heavy weight of the door can complicate these issues and make them more severe until it becomes risky to operate your door.

Something Is Wrong With Your Transmitter

There could possibly be a number of issues that is causing your transmitters not to function appropriately or if the garage door doesn’t open with the remote. The most familiar reason could be that you’re just out of range of your garage door. Each garage door and transmitter combo has a particular range it will operate in. In the event you know you’re in range and the door still won’t open, inspect to ensure the antenna is hanging down from the motor inside your garage and is not blocked. Your antenna ought to be totally free from any blockage to clearly receive the signal to open and close the door.

Something Is Blocking The Door’s Path

Garage doors are made with a reversing system that stops them from crushing objects in their way. If you notice that your garage door does not open all the way or closes part way and then goes back up, this is often caused by objects on the ground blocking their way like garbage cans or toys. It might also be caused by a buildup of debris on the tracks that hinders the rollers from moving. If the door seems to strikes even a very small object on the track, it will return back up to avoid crushing it.

Your Springs Are Broken

In the event that your garage door does not open all the way or suddenly won’t move up and you’re certain the transmitters are functioning properly and power is getting to the motor, you may have broken torsion springs. Doors may have one or two torsion springs. If any spring is broken, the garage door opener may find it hard to lift the weight of the door or cannot open the door at all. The springs are an important aspect of the doors operating system as they act as an eliminator of the weight and holds the tension so that the cables can lift the door.

The Garage Door Limit Settings Isn’t Set Properly

At times, you’ll observe that your garage door shuts completely and then instantly goes back up instead of staying in the already closed position. This problem generally arises with new garage doors that were just mounted or old models that may need to be reset. If this occurs, the most likely cause is the open and close limit settings of the garage door opener.

The Disconnect Switch/Safety Release Was Enabled

Whenever you can hear your garage door motor functioning for what seems like the full time frame it usually would take to open or close the door, but the garage door is not opening fully, most likely the disconnect switch or safety release cord is enabled. Every garage door opener comes along with a disconnect switch in the event that you lose power. This enables you to open or shut the door manually so your vehicle isn’t rapped in the garage until the power comes back on.

The Door Was Manually Locked

If your garage door will not open manually or with the opener, but the opener motor works for little time and then shuts off, the garage door might have been manually closed. If you’ve examined the door springs and the track for obstructions, and those things seem to be fine, find out if the lock on the door is engaged. If the door is locked and the door opener has been engaged, this may cause damage to both the opener and the door.

The Tension Springs Or Cable Are Broken

Garage doors have tension springs and cables that slowly and easily lower your door while closing. If these tension springs or cables break up, you will probably notice that your garage door shuts quickly, usually with a resounding bang when it hits the floor. This is often extremely dangerous as there is nothing stopping the garage door from crushing something that might be below it.

Garage Door Repair – Here Are Additional Repair Tips:

Step 1: Check out the metal tracks inside the garage. Examine the mounting brackets that confine the tracks to the surfaces. If they’re unfastened, stiffen the bolts or screws at the brackets. Inspect the tracks for dents, crimps, or flat spots. If you find any ruined spots, hit them out with a rubber mallet, or with a hammer along with a block of scrap wood. If the tracks are severely ruined, they need to be replaced. It may be best to hire an insured professional to inspect parts of the garage door for health and safety reasons.

Step 2: Check the tracks with a level to ensure they’re correctly aligned. Horizontal tracks need to slant a little down in the direction of the back of the garage; if you are dealing with roll-up doors, the vertical sections of the track must be exactly plumb. Both tracks will have to be at the same height on the wall. If they are not correctly aligned or loose but do not take out the screws or bolts that grip the mounting brackets and tap the tracks cautiously into position. Recheck the tracks with the level to ensure they really are in the appropriate position; then firm up the screws or bolts at the mounting brackets.

Step 3: Thoroughly clean-up the tracks with household cleaner to take out dirt and toughened grease. Thoroughly clean the rollers carefully, and wipe each tracks and rollers dry.

Step 4: Consider checking the springs load once you are able to lift the door manually. You can do this by lifting the door. Operating the door manually should be relatively easy with little resistance. If it difficult to manually operate the door, then it may be out of balance. It is highly recommended that a trained service technician takes a look at the door in order to establish the best way forward.


Need A Garage Door Repair? Click Here<<<<

Need Help From One Of Our Experts? Give Us A Call Today 206-934-1234